Long road, but we're here

[AudiSport]

After 3+ years I finally got the car on the road again. I purchased it in summer of 2020 and blew the head gasket the next year. And in the middle of a home remodel, it didn't get touched for a while then work was slow.

Car was equipped with a Vitesse system and I didn't care for it, so I pulled it out.

Welded up a new 3" downpipe

IMG_6657.JPEG (1000.01 KiB) Viewed 525 times

Installed a new SCE gasket

IMG_4545.JPEG (819.5 KiB) Viewed 525 times

Installed some ARP studs

IMG_4566.JPEG (1004.22 KiB) Viewed 525 times

Designed my own cam sync housing, 3D print to test, finished is Anodized 6061

IMG_7753.JPEG (894.25 KiB) Viewed 525 times

IMG_7481.JPEG (758.3 KiB) Viewed 525 times

IMG_7479.JPEG (1.37 MiB) Viewed 525 times

IMG_0552.JPEG (841.4 KiB) Viewed 525 times

Designed my own DBW throttle body adapter again in 6061 anodized

IMG_7781.JPEG (812.44 KiB) Viewed 525 times

IMG_7780.JPEG (575.36 KiB) Viewed 525 times

Mounted the coils on the cam box, installed new insulated fuel lines from BAT, Nuke fuel rail and Radium FPR with Honeywell MIP sensor for Maxx

IMG_7951.JPEG (1.31 MiB) Viewed 525 times

Built my own wire harness for the MaxxECU

IMG_2387.JPEG (531 KiB) Viewed 525 times

IMG_0998.JPEG (997.88 KiB) Viewed 525 times

Currently learning Maxx and a friend is helping me get it going. The car is drivable. But more to be tuned.

[AudiSport]

Reached max attachments so...

Active priorities to be done over the winter:
refresh suspension
rebuild sport seats
finish wheel rebuild
finish stereo display/messages panel with MFD28 CANchecked display

IMG_2559.JPEG (847.32 KiB) Viewed 524 times

IMG_2628.JPEG (1.01 MiB) Viewed 524 times

IMG_2661.JPEG (1.32 MiB) Viewed 524 times

IMG_2613.JPEG (768.14 KiB) Viewed 524 times

[Tom]

Awesome work on so many fronts! Every picture deserves a thread of its own! Congrats on getting it going. Very interested to hear how that head gasket does over time!

p.s., is that an actual store name in Iowa??

[AudiSport]

Awesome work on so many fronts! Every picture deserves a thread of its own! Congrats on getting it going. Very interested to hear how that head gasket does over time!

p.s., is that an actual store name in Iowa??

Yes, it was. They were acquired by Maverick out of Utah recently and are changing the name.

[Fejjj951]

Awesome work on so many fronts! Every picture deserves a thread of its own! Congrats on getting it going. Very interested to hear how that head gasket does over time!

p.s., is that an actual store name in Iowa??

I helped develop this HG with SCE/Athena a few years ago. The initial group buy was ~50. I have not heard of a single person having any issues with these. I went through 2 Cometics before installing 1 in one of my 89’s.

[ROB III]

@AudiSport
Impressive set up and kudos to your dedication!

[Spencan]

I installed that same HG in May 2024 and so far so good. I have gone as high as 19 psi of boost.

[944m3]

Congrats on getting her back on the road.

I purchased the CANChecked 28 as well for my MaxxECU. But then switched to an Android double din head unit and installed Realdash. It’s connected to the ECU via wired CANbus. Pretty straightforward. I love the size of the screen to really look at data. Realdash is awesome. And once you figure out CANbus it’s really easy to use.

I’m also looking into sequential ignition and fueling. Do you find it changed anything as far as drivability or MPG?

[AudiSport]

Not yet, I've put maybe 20 miles on it since getting it running. Trying to dial in cold start and tune settings.

[t36]

Wow! Amazing!
And wicked taste in music too.